How to Replace a Bathtub in Your Bathroom
How to Replace a Bathtub in Your Bathroom
Blog Article
Right here in the next paragraph you can get more good guidance when it comes to How to Install a Bathtub Yourself.
Setting up a tub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently obtainable, the task can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need an assistant to vacate the old bathtub as well as set in the new one. Make certain you have qualified on your own for the work and also fit trying it. Instead of hiring a professional to take over a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly assist you install a brand-new bath tub in your shower room if you have already acquired a brand-new tub and do not require to change the arrangement of your previous water pipelines.
Your tools and also product checklist should consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome because of the restricted accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. When the supply pipes have been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will require a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers are in place between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The previous kind should be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Using the two wooden boards under its feet, put the bath tub in the called for placement. The wooden boards are handy in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The next goal is to make sure that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up faucets, fit the bottom of the furthest flexible tap port to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and check all joints and also brand-new pipework for leakages and also tighten them if needed. Fill up the tub and likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will certainly resolve it into its final position.
Planning for the Installment
First of all, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the versatile tap ports to the bottom of both faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealant can break relatively very early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that piece of writing was beneficial. Appreciated our write up? Please share it. Help another person find it. Many thanks for going through it.
Visit The Following Page Report this page